The Longwinded Making of the Hagrid's Hut - The Interior

Hey! You've found the third part of my Hagrid's Hut walk-through: The Interior

The completed Hagrid's Hut can be found HERE. 

Because I added a number of elements to the Octagon Room Box used to make this project, I wanted to create a rundown of the basic construction. There's a lot to go through, so I've broken it up into three parts: The Exterior, The Roof, and The Interior.

When making this project I alternated working on the inside/outside as glue/paint dried. So don't feel like you have to complete one area before moving on. 

Finally, I won't be going into fine details here, but I think these steps will be helpful if you want to create a similar project.

Now, on to the interior...

The first thing I've done inside is to plot a horizontal like where my wall will be divided between wallpaper and plaster. I've also marked where the door will be placed.

Using those mark areas as a guide I'm applying a quick coat of plaster. You definitely do not have to do this, but I want to create a sort of plaster and beam Tudor effect.

A fireplace is essential in the hut, and I'm making a simple one from layers of cardboard.

It takes up almost and entire wall, but it's going to be a great focal point! You'll want to mark the size/shape of your fireplace on the wall, and be sure to include the size of the opening.

Paint the area behind the fireplace black.

Using the Small Stone Wall Stencil and some acrylic latex silicone... voila! A stone texture, easy peasy. You could use this same stencil on the exterior, but I prefer the size of the large egg carton slabs.

Once dry, I painted my hearth white. I also created a top mantelpiece, and a slab for the fireplace to sit upon (not pictured). Put these aside for now while we work on that room!

Wallpaper is added to the lower portion of the wall (from A Summer Gnome Home Paper Set) minding the placement of the fireplace. The flooring has also been added. The light coat of plaster has been given a coat of white paint.

Using strips of lightweight cardboard, I've made rails and baseboard trim. They're painted green to match the door which had also been installed. One important note: I made a mistake installing my trim and ran it straight across the entire wall. Be sure to NOT cover the area of the fireplace. You want that black area to be an empty pit of darkness, not cute green baseboards.

The floor looks lighter here because I've sanded the surface of the paper used for the flooring (a wood themed sheet from A Summer Gnome Home Paper Set). I will stain it slightly darker and I needed to rough up the surface in order to do that.

Again, simply using strips of light cardboard, I've created a sort of wooden 'Tudor beam' effect.

I've 'refinished' the floors with a few light washes and installed the fire place.

You can now age the room if you like, adding dirt and grime. Be sure to add some soot to your fireplace. Honestly I think I should have added far more grime here, but Hagrid might appreciate that I cleaned the place up a bit.

Once the roof is on, you'll want to break up that big space.

One way to do that is by adding more beams. And just like the grime, you can go a bit nuts here and making patterns and designs with your beams. 

Seriously, check out this beautiful historical sample!

The final step is to clean up your edges, and with all those bits in place, the REAL fun begins! Plan and plot the layout of the furnishings and accessories. I'm sure you'll absolutely no problem filling it up :)

~

You can browse all of the sweet, sweet AlphaStamps items used in this project HERE 

The additional items used in it the construction:

• corrugated cardboard
• thin cardboard
• acrylic paint
• glue

• acrylic latex silicone

• drywall compound

• twigs and bark
• miscellaneous bits n' pieces

The Longwinded Making of the Hagrid's Hut - The Roof

You've found the second part of my Hagrid's Hut walk-through: The Roof

The completed Hagrid's Hut can be found HERE. 

Because I added a number of elements to the Octagon Room Box used to make this project, I wanted to create a rundown of the basic construction. There's a lot to go through, so I've broken it up into three parts: The Exterior, The Roof, and The Interior.

When making this project I alternated working on the inside/outside as glue/paint dried. So don't feel like you have to complete one area before moving on. 

Finally, I won't be going into fine details here, but I think these steps will be helpful if you want to create a similar project.

On to the roof!

I created a roof using corrigated cardboard. Cut four triangles measuring 6.25" wide at the base and 9" tall. Take one of those triangular pieces and cut in half, vertically.

Arrange the cut pieces as they appear in the top image. The two half pieces on either end, the three large pieces in the middle. It's like a terribly cut pizza.

Using tape, join those pieces together ON ONE SIDE ONLY. I used hockey tape, eh, but you can use whatever you have on hand. The pieces SHOULD be able bend and move.

On the side with the tape, cover with paper that you want for the ceiling/interior roof of your hut. Make sure that the pieces are still flexible.

Now, you're going to want to do a bit of fiddling around with placement. The roof should bend nicely to the top edge of the hut, you just need to find the sweet spot where it fits just so. When you find it, add some tape to maintain the angle...

... then glue to the top edge with hot glue to secure in place. Try not to get too messy with the glue on the inside, instead using a bead of glue around the exterior overhang.

The roof is short and stout. If you'd like to experiment and make something taller and spikier, you'll want to add to the height of the triangles, while maintaining the width. 

I've added a smokestack extending from my roof. This too is made from cardboard, the sides taped. I wasn't worried about a hole in the chimney as I knew I'd be adding a raven perched on the top. You may want to consider constructing your chimney like an open-ended box to include an opening.

Use drywall compound on the stack, just as you did at the side of the house. 

Paint the surface of the roof black. Again, this is very useful for camouflage purposes, no matter what material you'll be using.

I'm using bark to cover my roof. It wasn't my first choice. I wanted to use coconut fiber which gives a wonderful, almost thatched roof effect. Whatever you do choose to use keep two things in mind.

1. Weight. This roof isn't meant to hold a great deal of weight so keep things light. You could reinforce the structure if you like, but if not, keep the weight of your materials in mind.

2. Remember those ugly corrugated edges. I simply added a bit of length to cover them up, but it's something you'll need to keep in mind.

Once the roof is covered in a layer of bark, I tuck moss here and there.

The roof was far too light for my liking so I darkened it up with a few washes of diluted paint.

You'll also notice I've started adding moss and grasses around the door and bottom edge. There's a Miniature Antique Brass Door Pull too... I may or might not have installed that upside-down.

Something still seemed to missing or just 'off' at this point. I added some snippets of twigs to look like roof supports and I really think they created balance.

In addition to more moss and grass, you can see the chimney has had a bit of age tossed at it.

Just keep adding loads light washes of grime and you'll have your brand new hut looking old in no time at all!

Next, the guts! Let's see the insides put together.  The Interior.

~ 

You can browse all of the sweet, sweet AlphaStamps items used in this project HERE 

The additional items used in it the construction:

• corrugated cardboard
• thin cardboard
• acrylic paint
• glue

• acrylic latex silicone

• drywall compound

• twigs and bark
• miscellaneous bits n' pieces

The Longwinded Making of the Hagrid's Hut - The Exterior

Hey! You've found the first part of my Hagrid's Hut walk-through: The Exterior

The completed Hagrid's Hut can be found HERE. 

Because I added a number of elements to the Octagon Room Box used to make this project, I wanted to create a rundown of the basic construction. There's a lot to go through, so I've broken it up into three parts: The Exterior, The Roof, and The Interior.

When making this project I alternated working on the inside/outside as glue/paint dried. So don't feel like you have to complete one area before moving on. 

Finally, I won't be going into fine details here, but I think these steps will be helpful if you want to create a similar project.

Now, on to the construction!

Start off by painting the base. You're going to be covering this up, but by preparing it now you're going prevent later issues and hide any flubs.

 

Once dry, cover the bottom of the base with some scrapbook paper. (top image) The reason I do this is because I'll be adding flooring later. I want the two sides of the chipboard to sort of have even 'coatings' or layers. In my experience this drastically reduces the chances of the chipboard warping later.

You also want to paint the funny looking frame that hold the walls in place and provides stability.

Slot your walls into the base and support them with the top funny looking bit. Add masking tape to each 'corner'. The masking tape helps to make the join where the walls meet more seamless when finishing.

Add masking tape to the inside joins too.

I know I want a fireplace inside my hut, so I'm making a chimney outside. I'm simply using layers of corrugated cardboard to create this. I tape the edges and add it to the side of my hut.

My exterior is going to have a stone finish, but I want to create interest by including another texture so I'm giving the chimney a plaster look. Using a pallet knife I smooth drywall compound over the surface. You could alternatively use grout, or acrylic latex caulk. Check out your local hardware store for ideas.

Take your time, and allow your compound to dry. You do not have to make it perfect all at once! Touch up the surface and add layers as you go along.

While Hagrid's Hut was wooden in the Potter books, I'm making a stone surface exterior. Tearing up egg cartons I create my stones. You'll likely want to prepare twice as much as you think you'll need. You can keep all the 'stones' evenly shaped/sized, or create patterns by mixing it up!

I begin adding my stones around the area that the door has been plotted. I'll frame in the door and then work outward applying horizontal lines of 'stonework' working from the bottom to the top. I try to keep things fairly straight as it's easy for things to start lining up wonky. Don't get too caught up in perfection though! A bit of wobble is a-ok.

Another layer on my chimney and the stones are looking dandy!

FYI, I use Aleene's Tacky Glue as it seems to keep things in place as I'm working. I don't have to worry about stones sliding all over the place as they dry.

Next, I take disposable piping bag, put some drywall compound inside, and cut the tiniest bit off the end. I'll use this to squiggle some 'mortar' between the stones. You need VERY LITTLE for this. In the above photo I've probably applied 2xs more than I should have.

With a wet finger, smooth out the plaster/mortar. If things get a bit messy, just use a damp cloth to remove the excess. Don't worry. It's going to look great!

A final coat on that chimney. See! It's coming along.

Once that dries you can try adding a bit more interest to your stonework. Remember that stones and rock have variation in their colouring. Consider trying chalk pastels, light washes of paint, ink, stain... heck, I even used a bit of eyeshadow (beware anything with shimmer) and coffee to stain mine. 

If you want to apply a topcoat to the surface, remember that this too might affect the colour. Try a little on some leftover carton to see how it dries before applying to the whole surface.

Now add your door into place. I've used the Rustic Door - 1:12. Rather than creating a door that opens and fiddling with cutting out the wall, I'm using two doors. One doors sits on the exterior wall, the other exactly opposite on the inside.

Now, let's pop over to making the roof to continue...

~

You can browse all of the sweet, sweet AlphaStamps items used in this project HERE 

Additional items used in it the construction:

• corrugated cardboard
• thin cardboard
• acrylic paint
• glue

• acrylic latex silicone

• drywall compound

• twigs and bark
• miscellaneous bits n' pieces

The Diviner's Table

It feels like an age since I posted a tutorial (probably because it has been). I thought that a Halloween surprise might be nice, so I created a little Diviner's Table and have a tutorial for the red pillar candles and incense.

While a tutorial is all about teaching others, I learned a lot myself while putting this wee table together. I learned more about Baphomet, the goat figure on the glass novena candles. Baphomet is actually a pretty complex character with an interesting history. I also experimented with resin. See those bubbles in the crystal ball? Pretty much drove me insane trying to minimize them.

There were some happy discoveries too, like this impossibly small smudge stick! We had been making regular size smudge sticks from white buffalo sage in the garden and when I spied the little leaves and bits leftover, drying on a table, I had a eureka moment. Why not make a wee one? And it's my new favourite thing. You can even burn them!!! (If you're very careful of course.)

If you'd like to see how this little piece came together, you can find the video HERE.

And if you're looking for a list of supplies, here are all the bits used in making this piece:
• 3" small wooden round (or other size you prefer)
• 3" unfinished wooden candlestick

• black acrylic paint
• glue white/wood glue, and instant/crazy glue
• crayons
• thin wire

• tooth picks
• bead and bead cap
• florist wire

Optional extras:

• resin or real crystal ball/marble/large glass bead

• tiny gem chips
• watch crystal (paint back black for scrying mirror)
• sage leaf and thread for smudge stick
• Tiny Tarot (the set of 22 Major Arcana used here, but full deck is available)

• ANYTHING YOU CAN IMAGINE!

 

Important note: If you can't find one of the products I used, please do improvise! Don't you dare overpay for materials. Those candlesticks shouldn't be more than a couple of dollars and I just spied them online at a ridiculously inflated price. You should be able to find them in most craft shops.

Also, while the crystal ball in the pic was a bit bubbly, I did end up finding a different resin that gave me much better results. I was super happy with Resinate UltraCast. No affiliate link, and they didn't provide me product, but I was pleased with my results and thought I'd share if anyone else is having resin struggles.

Art Walk 2021 Giveaway

I cannot believe it's been over a month, A MONTH!!! since my last post. Cross my heart I've been working away, playing with resin, fiddling about, canning and preserving the last of our garden spoils. I've also got a big fat glorious project I can't share just yet... but I promise you're going to love.

I've mentioned that I'll be teaching with Art Walk Alchemy 2021 - "Enigmas and Curiosities". Super excited about that and I hope you'll join me. Right now they're doing a giveaway for a free registration, so why not tip your hat into the ring.

For your chance to win:

• Go to Mystic Spring Studios’ Facebook page HERE

• Add a Halloween project that you have created and tag me.

• Share the giveaway

That's it!

To find out more about Art Walk Alchemy 2021, click HERE

The giveaway ends on October 30 and the winner will be announced on Halloween!

Best of luck to you!

Bees bees bees

The garden is particularly abundant with blooms at the moment. It was tremendously dry last month and everything was crispy brown. I prefer the happy fuchsias and yellows. With those blooms comes bees and butterflies and hummingbirds. I just love watching them. Not so thrilled with the wasps who have also come out whom I swear a blue streak to when they near. Bumble and honeybees on the other hand are a delight.

All that babbling is to introduce this cute set of bumblebees that I made, inspired by my garden visitors. 

They're simply made of balls of paperclay, painted with acrylic. I've added beads added for eyes, and Printed Bee Wings on Transparency . Finally I pushed in a small loop/hook, and added string to give them flight.

I think they're stonkin' cute. How adorable would they bee as a mobile with paper flowers? Gah!

One of the chubby dudes did escape from my craft room, but he was soon discovered in the garden.

He was lured back inside with promises of warm, soft, ginger cookies and tea.

Hope you're dandy and healthy and safe.

xoxo

Jane Austen, French Knots and Small Celebrating Small Successes

Wayyyy back in May, I received a copy of "Jane Austen Embroidery" by Jennie Batchelor and Alison Larkin. It's super pretty and I was totally enthusiastic about stitching my days away, dreaming of Mr. Darcy (or Colonel Brandon if you please *swoon*) but honestly... life got in the way and I drank too much gin that weekend.

I am not a sewist or embroiderer, or in any way skilled with a needle and thread, but I do love embroidery and keen to try my hand at most craft skills. I thought I'd start with a little snip from one of the designs to sort of warm up before committing to a big project.

 

Those of you with greater needlework skills are probably groaning at my wonky work, but I was really pleased with that tiny hoop (which is 3" across if you were wondering). It's given me the confidence and desire to create a larger project from the book. With this tiny hoop I tried a couple of new techniques, and while far from perfect, I think there's charm in that not-quite-right thread.

Now, a number of the designs in the book included french knots, which have always eluded me. Many attempts have been made over the years, and I have always failed. I decided to try again, adding them to my wee hoop, and this time I would create a french knot before bed or never sleep again. And you know what? I did it! 

Were those knots perfect or dainty? Not in the least... BUT I DID IT! Dainty perfection will come with time and practice.

Until perfection comes, I've celebrated my small victory by making a charm with a group of the biggest chonkiest french knots you ever did see. Made with the chunkiest wool, in the tiniest embroidery hoop. 

It might look like a mess of lumpy wool to others, but to me that's proof of one small success, of victory, of the baby steps it takes to move forward.

Remember to love all your chunky knots, my friends. Take pride in every milestone no matter how wonky, or wobbly they appear.

I think I'm ready for that bigger project and some Colonel Brandon day dreams.

If you're interested in purchasing "Jane Austen Embroidery" please consider supporting your local independent book seller. It can also be found here on Amazon (direct, non affiliate link).